What are soldering fume extractors and where are they used in industrial applications?

Soldering fume extractors are specialized ventilation systems designed to capture and filter hazardous particulates, gases, and vapors generated during soldering processes. These systems are essential in electronics manufacturing, automotive component assembly, aerospace wiring harnesses, and medical device production where lead-free solder alloys produce fine particulates below 0.3 microns. Industrial applications include PCB assembly lines, cable harness production, and component-level repairs where flux residues and metallic fumes pose respiratory hazards. Modern extractors like the ULT ASD series provide airflow rates from 120 to 1000 m³/h with static pressures up to 12,000 Pa for demanding industrial environments.

What technical specifications should be considered when selecting a soldering fume extractor?

Critical selection parameters include volumetric airflow rate matching your application requirements, with compact systems like the ULT ASD 300 providing 250 m³/h at 2,000 Pa for single workstations, while industrial units such as the ULT ACD 1200 deliver up to 1,000 m³/h at 1,800 Pa for multiple stations. Static pressure capability determines the extractor's ability to overcome filter resistance and ductwork losses, with values ranging from 1,400 Pa for basic applications to 12,000 Pa for high-resistance HEPA filtration systems. Filter efficiency specifications must address both particulate removal for metallic fumes and activated carbon capacity for organic flux vapors. Power consumption, noise levels below 65 dB(A), and motor protection ratings also influence operational costs and workplace acceptance.

Which safety standards and certifications apply to industrial soldering fume extraction systems?

Industrial soldering fume extractors must comply with EN 61010-1 for electrical safety in laboratory equipment and IEC 61000-6-2 for electromagnetic compatibility in industrial environments. ATEX certification is mandatory for units handling flammable solvent vapors, with Ex-rated models like the ULT ACD 400 Ex designed for Zone 1 and Zone 2 hazardous areas. Filter performance standards include EN 1822 for HEPA efficiency testing and ISO 29463 for EPA filter classification, ensuring minimum 99.95% efficiency at 0.3 micron particle size. Occupational exposure limits follow EN 689 guidelines, requiring extraction systems to maintain workplace concentrations below 0.1 mg/m³ for lead compounds and 5 mg/m³ for rosin-based flux fumes according to German MAK values.

What are the differences between ASD particulate extractors and ACD gas/vapor extraction systems?

ASD series extractors like the ASD 300 MD.14 are optimized for fine dust and metallic particulate removal using multi-stage filtration with pre-filters and HEPA final stages, achieving 99.97% efficiency at 0.3 microns with airflow rates of 250-400 m³/h. ACD series units such as the ACD 400-1-V target gases, vapors, and odors using activated carbon adsorption stages, providing 400-1000 m³/h airflow specifically designed for organic solvent vapors and flux decomposition products. LAS laser smoke extractors like the LAS 500.1 HD.14 combine both technologies with 200 m³/h capacity at 7,500 Pa static pressure for high-concentration applications. Ex-rated variants include explosion-proof motors and antistatic components for handling flammable vapor concentrations above lower explosive limits.

What installation requirements and connection options are available for soldering fume extraction systems?

Most industrial soldering fume extractors require single-phase 230V power supply with earthing connections meeting IEC 60204-1 standards, while high-capacity units like the ULT ASD 1200 may require 400V three-phase connections. Ductwork connections utilize standard 100mm, 160mm, or 200mm diameter flexible hoses with antistatic properties rated for continuous 60°C operation, while benchtop units accept 75mm diameter extraction arms with 360-degree articulation. Installation clearances require minimum 500mm service access around filter compartments and 200mm above units for maintenance operations. Control integration options include 4-20mA analog signals for airflow monitoring, digital I/O for filter change indication, and RS485 Modbus communication for integration with building management systems or production line controls.

What safety ratings and environmental specifications apply to industrial fume extraction equipment?

Industrial soldering fume extractors typically feature IP54 ingress protection rating for dust and splash resistance in manufacturing environments, with motor housings rated IP55 for enhanced moisture protection. Operating temperature ranges span -5°C to +40°C ambient conditions, while filtered air temperatures can reach 60°C continuous duty without derating airflow performance. Static pressure capabilities range from 1,400 Pa for basic applications to 12,000 Pa for high-resistance filtration systems, with variable frequency drives maintaining constant airflow despite filter loading. Sound emission levels remain below 65 dB(A) at 1 meter distance to comply with EN ISO 3744 workplace noise regulations. Units handling flammable vapors require ATEX Zone 1 certification with temperature class T3 (200°C surface temperature limit) and electrical equipment group IIA for most solvent applications.

What maintenance intervals and service requirements are needed for soldering fume extraction systems?

Pre-filter elements require replacement every 3-6 months depending on particulate loading, with differential pressure indicators triggering maintenance at 80% filter saturation typically around 800-1000 Pa pressure drop. HEPA final filters maintain efficiency for 12-18 months in normal soldering applications, with replacement intervals determined by airflow reduction below 80% of nominal capacity rather than fixed schedules. Activated carbon stages in ACD gas extraction units require renewal every 6-12 months based on breakthrough testing for target contaminants, with spent carbon disposal following hazardous waste regulations. Motor bearing lubrication follows manufacturer specifications typically requiring high-temperature grease application every 2000 operating hours, while fan impeller cleaning and electrical connection inspection occur during annual preventive maintenance cycles to ensure continued performance and safety compliance.

Fume Extractions - ESD (antistatic)

Soldering

We can't find products matching the selection.

Solder fume extractors remove hazardous flux activator vapors, rosin aerosols, and fine particulates generated during hand soldering, rework, and wave soldering processes. High-performance units achieve airflow rates from 60 to over 1,000 m³/h, with multi-stage filter systems combining pre-filters, HEPA H14 filters (EN 1822), and activated-carbon stages that capture particles down to 0.3 µm at >99.995% efficiency. Extraction arms typically cover a capture radius of 100-400 mm at source velocities of 0.5-1.0 m/s, ensuring compliance with workplace exposure limit (WEL) requirements under EN 482 and IFA measurement standards.

As a specialist distributor for soldering technology, esd.equipment stocks 823 solder fume extraction products from leading manufacturers including ULT, Alsident, OKI, Quick, JBC, Weller, BOFA, and Ersa - covering bench-top single-operator units, central extraction systems, and integrated fume extraction soldering stations, all meeting IEC 62841, EN ISO 21904, and TRGS 900 requirements.

ULT Solder Fume Extraction ACS, LPA, FPE series - HEPA H14, 60-1,000 m³/h, EN ISO 21904 Fume Extraction Alsident System 50/75/100 extraction arms, 0.5-1.0 m/s capture velocity, DN50-DN100 OKI Solder Fume Extraction Compact bench-top units, integrated filter, for OKI soldering stations Quick Solder Fume Extraction Single- and multi-operator extractors, activated carbon + HEPA combination filters JBC Solder Fume Extraction FAE, FUE series - compatible with JBC stations, HEPA H13/H14, quiet <48 dB(A) Weller Solder Fume Extraction Zero Smog EL/TL series, 12-230 m³/h, filter life indicator, IEC 62841 BOFA Solder Fume Extraction AD Oracle, ProMax series - up to 550 m³/h, 3-stage filtration, EN ISO 21904 Ersa Solder Fume Extraction EASY ARM, POWER CUBE series - modular, 80-400 m³/h, compatible with Ersa stations

Key technical advantages - Solder Fume Extraction at a glance

🛡 HEPA H13/H14 filtration - captures particles ≥0.3 µm at >99.95-99.995% efficiency (EN 1822)

⚡ 60-1,000 m³/h airflow - covers single-operator bench to multi-station production lines

🔍 3-stage filter systems - pre-filter + HEPA + activated carbon for flux vapor and aerosol removal

⚙ Modular extraction arms - DN50-DN100, 100-400 mm capture radius, flexible positioning

📝 EN ISO 21904 compliant - meets IEC 62841 and TRGS 900 workplace exposure limits

✓ 823 products in stock - ULT, BOFA, Weller, JBC, Ersa, Alsident, OKI, Quick

ULT vs. BOFA vs. Weller vs. JBC - Solder Fume Extractor technical comparison

Criterion	ULT	BOFA	Weller	JBC
Airflow range	60-1,000 m³/h	up to 550 m³/h	12-230 m³/h	ca. 20-150 m³/h
Filter class	HEPA H14 (EN 1822)	HEPA H14	HEPA H13	HEPA H13/H14
Filter stages	3-stage (pre + HEPA + carbon)	3-stage	2-3 stage	2-stage
Noise level	ca. 45-55 dB(A)	ca. 48-58 dB(A)	ca. 45-52 dB(A)	<48 dB(A)
Application scope	Bench-top to central systems	Bench-top to multi-station	Bench-top, station-integrated	Station-integrated, bench-top
Norm compliance	EN ISO 21904, IEC 62841, TRGS 900	EN ISO 21904, CE	IEC 62841, CE	CE, EN ISO 21904
Filter life indicator	Yes - visual/electronic	Yes	Yes	Model-dependent
Extraction arm option	Yes - DN50/DN75/DN100	Yes	Yes (Zero Smog range)	Yes (FAE/FUE series)

Solder Fume Extractor product overview - series by application

Series / Brand	Application	Performance	Key feature
ULT ACS / LPA	Central extraction, multi-station	up to 1,000 m³/h	Modular, scalable, HEPA H14
BOFA AD Oracle / ProMax	Multi-operator, SMT rework	up to 550 m³/h	3-stage filtration, digital control
Ersa POWER CUBE / EASY ARM	Bench-top, Ersa station pairing	80-400 m³/h	Modular arm system, quiet operation
Weller Zero Smog EL/TL	Single-operator, bench-top	12-230 m³/h	Filter life indicator, IEC 62841
JBC FAE / FUE	JBC station integration, rework	ca. 20-150 m³/h	Low noise <48 dB(A), HEPA H14
Alsident System 50/75/100	Flexible arm extraction, bench	DN50-DN100, 0.5-1.0 m/s	Articulated arm, 100-400 mm radius

Typical application areas: Electronics manufacturing and SMT rework (IPC-A-610, EN ISO 21904), semiconductor assembly (SEMI S2, TRGS 900), medical device production (ISO 13485, IEC 62841), automotive electronics (IATF 16949, VDA 6.3), aerospace and defense soldering (AS9100, IPC-7711/7721), laboratory and R&D workstations (EN 482, DGUV Regel 109-002)

✓

823 Products in Stock ULT, BOFA, Weller, JBC, Ersa, Alsident, OKI, Quick

🛡

EN ISO 21904 & IEC 62841 Compliant HEPA H13/H14 filtration, TRGS 900 workplace limits

⚡

60-1,000 m³/h Extraction Power From single-operator bench to central production systems