Hakko FT 710-05. Lötspitzenreiniger mit rotierenden Bürstenwalzen A (Kunststoff) incl. Aufnahme A + B
221,24 €
185,92 €
exkl. Versandkosten
Artikel
HK-FT-710-05
Hersteller-Nr.
FT 710-05
Lötspitzenreiniger mit rotierenden Bürstenwalzen A (Kunststoff) incl. Aufnahme A + B
Bilder dienen als Referenz und sind möglicherweise nicht genau, das tatsächliche Produkt kann abweichen.
| Tip cleaner having both wire-type and sponge-type advantages | |
 | Prevents solder from splashing when cleaning. |
| · Inserting just the tip into the receptacle completely prevents solder from splashing. | |
  | |
 | Two-types of brushes control how much solder is removed. |
| · Solder removal status can be adjusted by plastic brushes and metallic brushes. | |
| With wire-type cleaners, excessive amounts of solder remain on the tip, which causes solder to splash when soldering. With sponge-type cleaners, oxidation is promoted, which causes shorter tip life. · A tip cleaner with both wire-type and sponge-type advantages eliminates the above problems when soldering. | |
| Comparison of how much solder is removed by the different cleaning methods< | |||
| * The photos show the iron tips T12-D24. | |||
 Enlarged images of cleaning brushes | |||
 | Minimizes decrease in temperature of the tip while cleaning. | |
| · Inserting the tip turns the brush automatically; no need to switch it on and off. · Reduces the tip cleaning time between soldering works to increase work efficiency. · The electric rotary cleaner provides a uniform final cleaning status with no differences between individuals. | ||
| Comparison of decrease in tip temperature by cleaning method | |||||||||
| If decrease in temperature is small, the time for a single cleaning also becomes short. Because cleaning is performed many times per day, the overall working time can be also shortened. | |||||||||
| Time for single cleaning (The time for a single cleaning is measured as the time until the tip temperature reaches the set temperature after cleaning.) | |||||||||
 | |||||||||
 | The low-noise design relieves stress due to noise during work. | |
| * This cleaner is very quiet in comparison with competitor's electric tip cleaner. | ||
 | Easy to maintain |  |
| · Easy-to-replace brushes | ||
| → Brushes can be replaced without removing any screws. | ||
| · Solder left inside is stored in "Solder waste collector". | ||
| → Solder does not splash all over the inside of the main body. | ||
| · Safe design prevents brushes from turning unexpectedly during replacement. | ||
| → The brush cannot be replaced unless the AC adapter is unplugged. | ||
 | This tip cleaner can be attached to HAKKO iron holders HAKKO FH-101, FH-200 and FH-201. | |
| · This tip cleaner can be attached to any of the above 3 iron holders using just 2 screws. For other iron holders, this tip cleaner can be placed next to the iron holder. | ||
 | * The HAKKO FT-710 itself cannot be used as an iron holder. Be sure to use it together with an iron holder. |
| Category | Title |
| How to use | Cleaning mechanism |
| How to use | How to ground the HAKKO FT-710 |
| How to use | Combinations of the HAKKO FT-710 and iron holders |
Packing List
| * Some soldering irons or tip shapes are NOT available. Please check 'Specification' if your soldering iron or tip shapes are available. |
| Part No. | Packing List |
| FT-710 | HAKKO FT-710, AC adapter, Receptacle A and B, Lock nut, Solder waste collector, Gauge, Instruction manual |
| NOTE: Optional Part Receptacle C being purchased, HAKKO 917(Discontinued) (Station HAKKO 938(Discontinued)) and HAKKO FX-8301(Station HAKKO FX-838) are also available. |
Specifications
| Model No. | FT-710 |
|---|---|
| Rating | DC 24 V 130 mA |
| Brush rotational speed | 2,500rpm |
| Standard receptacle | Receptacle A and B |
| Dimensions | 71(W)×77(H)×107(D) mm |
| Weight | 450g |
・AC Adapter
| Output voltage | DC 24 V |
|---|
| Applicable Soldering Iron List |
| Receptacle | Soldering tip | Unusable shape | Custom-ordered shape | Soldering iron |
| Receptacle A | T7 series | T7-JL02 Spatula | T7-KF | HAKKO FM-2027 Station: HAKKO FM-202 (Discontinued) |
| T11 series | - | - | HAKKO FX-901 | |
| T12 series | T12-JL02 Quad Tunnel Spatula | T12-WB2 T12-WD08 T12-WD12 T12-WD16 T12-WD52 T12-WI T12-DL52 T12-KF | HAKKO FM-2027/2028 for Japan, Oceania, Asia & Other countries Station: HAKKO FM-203, HAKKO FX-950, HAKKO FX-951, HAKKO FX-952, etc. | |
| T15 series | T15-XD15 T15-JL02 T15-JD14 T15-JD16 T15-R48 Quad Tunnel Spatula | T15-1603 T15-1605 T15-BC15 T15-BC28 T15-CF2 T15-CF3 T15-SB03 | HAKKO FM-2027/2028 for North America & EU. Station: HAKKO FM-203, HAKKO FX-950, HAKKO FX-951, HAKKO FX-952, etc. | |
| Receptacle B | T14 series | - | - | HAKKO 957 (Discontinued) |
| T18 series | - | - | HAKKO FX-8801 Station: HAKKO FX-888 (Discontinued), HAKKO FX-888D | |
| T34 series | - | - | DASH:FX-650 series | |
| 900 M series | 900M-T-H 900M-T-1.8H | 900M-T-LB 900M-T-1.2LD | HAKKO 900 Type Medium HAKKO 907 Station: HAKKO 928 (Discontinued), HAKKO 936 (Discontinued), HAKKO 937 (Discontinued) etc. | |
| Receptacle C (Optional Part) | T10 series | - | T10-J02 T10-K T10-KL T10-KU T10-LB T10-LI | HAKKO 917 (Discontinued) Station: HAKKO 938 (Discontinued) |
| T13 series T17 series | - | - | HAKKO FM-2026 Station: HAKKO FM-203, HAKKO FX-950, HAKKO FX-951, HAKKO FX-952, etc. | |
| T20 series | - | T20-K T20-KU T20-BL T20-BL2 T20-BL3 | HAKKO FX-8301 Station: HAKKO FX-838 | |
| T22 series | - | T22-C3 T22-BL T22-BL2 T22-D45 T22-J02 T22-K | HAKKO FM-2030, HAKKO FM-2031 Station: HAKKO FM-206 | |
| Receptacle, custom-designed | T19 series | - | - | HAKKO FX-8805 Station: HAKKO FX-889 |
| T33 series | T33-BC2 T33-BC3 T33-BC4 T33-BC5 T33-BC6 T33-D24 T33-D32 T33-D5 T33-D6 T33-1610 T33-1611 | T33-SSBC2 T33-SSBC3 T33-SSBC4 T33-SSBC5 T33-SSD24 T33-SSD32 T33-SSD16 T33-SSD6 T33-SS1610 T33-SS1611 | HAKKO FX-8802 Station: HAKKO FX-801 | |
| PRESTO series | - | - | HAKKO PRESTO |
 | *Soldering iron other than listed above (HAKKO FX-100, HAKKO FM-2032, Built-in solder feed type, Nichrome heater type and HAKKO 455/456), and Desoldering / Rework are not available. |
Replacement parts
| Part No. | Name | Specifications | |
|---|---|---|---|
 | B3523 | Lock nut | |
 | B3517 | Receptacle A | |
 | B3518 | Receptacle B | |
 | A1566 | Cleaning brush A (plastic brushes, qty 2) | |
 | B3521 | Solder waste collector | |
 | B3520 | Pulley belt |
 |
| *Some soldering irons and tip configurations cannot be used with receptacles A/B. Be sure to confirm applicable soldering irons and tip configurations from the applicable soldering iron list. |
| * Optional Part Receptacle C being purchased, HAKKO 917 (Station HAKKO 938) and HAKKO FX-8301(Station HAKKO FX-838) are also available. |
Options
| Part No. | Name | Specifications | |
|---|---|---|---|
 | A1567 | Cleaning brush B (metal brushes, qty 2) | |
 | B3519 | Receptacle C |
*Some soldering irons and tip configurations cannot be used with receptacles A/B.
Be sure to confirm applicable soldering irons and tip configurations from the applicable soldering iron list .
Maintenance
| Category | Title |
|---|---|
| How to use | Cleaning mechanism |
| How to use | How to ground the HAKKO FT-710 |
| How to use | Combinations of the HAKKO FT-710 and iron holders |
| Maintenance | Day-to-day cleaning |
| Maintenance | Maintenance and replacement frequency of the cleaning brush |
| Maintenance | Why can no solder be removed? |
Video
| Preview | Title |
|---|---|
 | how to clean a tip |
| Ausführung | TEC |
|---|---|
| Hersteller-Nr. | FT 710-05 |
| Hersteller | Hakko |
| Ursprungsland | Japan |
| EAN | 4962615034985 |
| Gewicht | 0.009900 |
| Hinweis | Es gibt keine Lieferung von Hakko Produkten in die Schweiz |
| Zolltarifnummer | 84609000 |
| GPSR Herstellerdaten | TBK - Technisches Büro Kullik GmbH Industriestrasse 27 DE-56276 Großmaischeid www.kullik.com |
| Artikel-Authentizität | Originalprodukt |
| Artikelzustand | Neu |
Download
Schreiben Sie eine Bewertung
Verwandte Produkte
Wählen Sie die Artikel aus, die dem Warenkorb hinzugefügt werden sollen, oder
