Quick connect coupling HI Cupla ACE HA-85SN, ø8.5 mm, PBT/POM - Nitto Kohki 317540870

Changing tools on an air line several times a shift means lifting the weight of the coupling every time. The Nitto Kohki HI Cupla Ace is made of engineering plastics (PBT, POM) and weighs a quarter of the steel HI Cupla, while still working up to 1.5 MPa.

• Engineering plastic body (PBT, POM) at a quarter of the weight of the steel version, a plug weighs 3 g to 17 g depending on the end configuration
• Working pressure up to 1.5 MPa, so the rating matches the steel couplings of the range
• Built-in automatic lock holds the sleeve once the connection is made and prevents accidental disconnection
• Connection by simply pushing the plug into the socket, no tools required
• NBR seal (marked SG) for -20 °C to +60 °C, approved media are air and water
• The plastic body is less likely to mark painted or easily dented surfaces than a metal coupling

Technical data from the manufacturer catalogue

Dimensions

Dimensions in millimetres. Values in brackets apply in the connected condition.

Legend: L = overall length; B = bore

Models in this series HI CUPLA ACE

Every model of the series as printed in the manufacturer catalogue. The row of the article offered here is highlighted.

Operating principle

• The weight is merely a quarter of steel HI CUPLA's and smooth push-in connection is achieved.
• Separation prevention mechanism for safety operation.
• Pressure ratings comparable to steel CUPLA.
• A built-in separation prevention mechanism locks the sleeve upon connection, thus prevents accidental disconnection.
• Just push plug into socket for simple connection.
• The weight is a quarter of steel HI CUPLA for easy handling.
• Can be used for air and water.
• Air flows in either direction from plug or from socket side when coupled.

Series comparison

Pick HI CUPLA ACE for air lines that need the 1.5 MPa {15 kgf/cm2} class together with a plastic body at a quarter of the weight of steel HI CUPLA and a sleeve lock against accidental disconnection; plastic plugs and Model HA-T stay at 1.0 MPa {10 kgf/cm2}. MICRO CUPLA, SMALL CUPLA, SUPER CUPLA, COMPACT CUPLA and CUBE CUPLA are rated 1.0 MPa {10 kgf/cm2} and come into question only where that lower pressure is sufficient, and COMPACT CUPLA and CUBE CUPLA where shut-off on both sides is required instead of the one-way shut-off of HI CUPLA ACE. Where the same 1.5 MPa {15 kgf/cm2} is needed in metal, HI CUPLA, HI CUPLA 200, FULL BLOW CUPLA and LINE CUPLA 200 remain available; HI CUPLA ACE is interchangeable with HI CUPLA models 10, 17, 20, 30, 40 and 60.

Body and seal materials

Applications

• Pneumatic tools on the shop air line with frequent tool changes
• Polyurethane hose from ø5 x ø8 mm to ø8.5 x ø12.5 mm on the PN and SN end types
• Water lines in the range up to 1.5 MPa
• Workstations with painted or thin-walled parts where metal couplings leave marks
• Two branch lines from one supply through the HA-T socket with inlet 20P-PLA and two HA-65S outlets

Compatibility

The range connects with HI Cupla models 10, 17, 20, 30 and 40 and is interchangeable with the Nut Cupla series and the HI Cupla series, except models 400, 600 and 800. Air flows in either direction once coupled, and the range is not suitable for vacuum in either the connected or the disconnected state.

Standards and compliance

End connections use Rc 1/4, Rc 3/8, R 1/4, R 3/8 and G 1/4 threads, the sealing material is nitrile rubber (NBR, marked SG).

Safety and application notes

• Before use, please be sure to read the Safety Guide described at the end of this book and the Instruction Sheet that comes with the products.

All technical data on this page is taken from the Nitto Kohki general catalogue Quick Connect Couplings C01en-b, page 61. The complete catalogue is available for download on this page.